Lincoln 2010 Navigator Uživatelský manuál

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Message center 19Entertainment Systems 30AM/FM stereo with CDX6/MP3 30Auxiliar

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

On vehicles with memory feature, to prevent damage to the steeringcolumn, the steering column is designed to set a stopping position justshort of the

OVERHEAD CONSOLEThe appearance of your vehicle’s overhead console will vary according toyour option package.Forward storage bin (if equipped)The stora

Power quarter rear windowsPress the VENT portion of thecontrol to open the power rearquarter windows.Pull the VENT control to close thepower rear quar

CLOCKPress the right (+) control to movethe time display forwards.Press the left (-) control to movethe time display backwards.AUXILIARY POWER POINT (

POWER WINDOWSWARNING: Do not leave children unattended in the vehicle anddo not let children play with the power windows. They mayseriously injure the

To operate one touch up:Pull the switch completely up to thesecond detent and release quickly.The window will close fully.Momentarily press the switch

INTERIOR MIRRORThe interior rear view mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side.

EXTERIOR MIRRORSPower side view mirrorsThe ignition can be in any position to adjust the power side view mirrors.To adjust your mirrors:1. Rotate the

Note: 10 or more switch activations within one minute, or repeatedfolding/unfolding of the mirrors while holding the switch rearward duringfull travel

WARNING: Never adjust the accelerator and brake pedal withfeet on the pedals while the vehicle is moving.POWER DEPLOYABLE RUNNING BOARDS (IF EQUIPPED)

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

Note: The running boards may operate slower in cooler temperatures. Inadverse conditions, debris such as mud, dirt, and salt may becometrapped in the

Using speed controlThe speed controls are located on the steering wheel. The followingbuttons work with speed control:RESUME: Press to resume a setspe

Increasing speed while using speed controlTo set a higher speed:• Press and hold SET + until you get to the desired speed, then release.You can also u

SYNC威 system hands freecontrol featuresPressbriefly to use the voicecommand feature. You will hear atone and LISTENING will appear inthe radio display

To open the moon roof: Press andrelease the SLIDE control, the moonroof will open automatically. Pressthe switch again to stop the moonroof.WARNING: W

HomeLink威Car2U威 Home AutomationSystemHomeLink姞 Wireless Control System (if equipped)The HomeLink威 Wireless ControlSystem, located on the driver’s viso

Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink威 equipped vehiclepurchase). I

5. Firmly press and release the “learn” or “smart” button. (The name andcolor of the button may vary by manufacturer.)Note: There are 30 seconds in wh

Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet

Car2U姞 Home Automation System (if equipped)The Car2U威 Home AutomationSystem is a universal transmitterlocated in the driver’s visor thatincludes two p

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa

Types of garage door openers (rolling code and fixed code)The Car2U威 Home Automation System may be programmed to operaterolling code and fixed code ga

1. Firmly press the two outerCar2U威 system buttons for1–2 seconds, then release.2. Go to the garage to locate thegarage door opener motor and its“lear

The indicator light above the selected button will turn on to confirm thatthe Car2U威 system is responding to the button command.To program another rol

Switchposition 12345678 9101112Up, onor +LLLLLLLLLLLLMiddle,neutralor 0MMMMMMMM M M M MDown,offor–RRRRRRRRRRRRL=left; M=middle; R=right3. To input the

After successful programming, you will be able to operate your Car2U威system by pressing the button you programmed to activate the opener.The indicator

POWER LIFTGATEThe liftgate can be operated by the following:• Instrument panel control button• Key fob button• Outside control button• Control button

Care should be exercised in starting the engine before the liftgate is fullyclosed (latched). If the ignition is cycled during a liftgate power closec

To close the liftgate with therear cargo area control button:Press and release the control on theleft rear quarter panel to close theliftgate. The chi

Note: In case of operation in extreme cold -40° F (-40° C), or onextreme inclines, manual operation of the liftgate is suggested.Obstacle detectionThe

Liftgate windowTo open the liftgate window, pressthe button on the left side of theliftgate above the license plate.CARGO MANAGEMENT SYSTEM (IF EQUIPP

Solid illumination after the engine is started indicates the On BoardDiagnostics System (OBD-II) has detected a malfunction. Refer to Onboard diagnost

To move the shelf to the dividerposition, pull up and pivot the shelfover the channels on the side trimpanels and snap vertically in place.WARNING: Do

To adjust the position of thecross-bar (if equipped):1. Loosen the thumbwheel at bothends of the cross-bar (bothcross-bars are adjustable).2. Slide th

KEYSYour vehicle may be equipped withtwo Integrated KeyheadTransmitters (IKTs). The key bladefunctions as a programmed keywhich starts the vehicle and

POWER DOOR LOCKSPress control to unlock all doors.Press control to lock all doors.Smart locksThis feature helps to prevent you from locking yourself o

The autolock feature repeats when:• any door is opened then closed while the ignition is in the on positionand the vehicle speed is 9 mph (15 km/h) or

Keyless entry keypad procedure1. Turn the ignition to the off position.2. Close all doors, the liftgate and liftgate window.3. Enter 5–digit entry cod

Power door lock switch autounlock enable/disable procedureBefore starting, ensure the ignition is in the off position and all vehicledoors are closed.

CHILDPROOF DOOR LOCKSWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo

The typical operating range for your IKT is approximately 33 feet(10 meters). A decrease in operating range could be caused by:• weather conditions,•

Two stage unlocking may be disabled or re-enabled by simultaneouslypressing theand controls on the IKT for four seconds (disablingtwo stage unlock all

Anti-lock brake system: If theABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected, have the systemserviced immediately by

Sounding a panic alarmPressto activate the alarm. The horn will sound and the turn lampswill flash for a maximum of three minutes. Press again or turn

3. A tone will be heard when the deactivation is complete.4. Repeat this procedure for another remote entry transmitter if desired.Replacing the batte

Illuminated entryThe interior lamps, parking lamps and puddle lamps (if equipped)illuminate when the Integrated Keyhead Transmitter or the keyless ent

• activate or deactivate the Autolock feature if equipped• release the liftgate glass,The keypad can be operated with the factory set 5–digit entry co

The anti-scan feature will turn off after:• one minute of keypad inactivity,• pressing thecontrol on the remote entry transmitter,• or the ignition po

engine. If a problem occurs, turn the ignition off, remove all objects onthe key chain away from the coded IKT and restart the engine.Note: Do not lea

Replacement Integrated Keyhead Transmitters (IKT) and codedkeysNote: Your vehicle comes equipped with two Integrated KeyheadTransmitters (IKTs). The I

Please read and understand theentire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition.2. Turn the igniti

Note: To program MyKey™ features, refer to MyKey™ in this chapter.MYKEY™The MyKey™ feature allows you to program a restricted driving mode topromote g

Create a MyKey™To program MyKey™ on one of the keys programmed to the vehicle,insert it into the ignition. Turn the ignition on. Use the message cente

Engine coolant temperature(RTT): Displays when the enginecoolant temperature is high. Stopthe vehicle as soon as safely possible, switch off the engin

Disable MyKey™To reset all MyKeys™ as Admin keys do the following:1. Turn the vehicle on using the Admin key.2. Press SETUP until PRESS RESET TO CLEAR

TroubleshootingCondition Potential CausesCan’t create a MyKey™ • Key in the ignition is already aMyKey™• Key in the ignition is the lastremaining Admi

The system is ready to arm whenever the key is in the off position, or isremoved from the ignition. Either of the following actions will prearm theala

Disarming the systemYou can disarm the system by any of the following actions:• Unlock the doors by using the remote entry transmitter portion ofyour

SEATINGAdjustable head restraintsYour vehicle is equipped with front row outboard head restraints that arevertically adjustable.WARNING: To minimize t

3. Lower the head restraint bypressing and holding the guidesleeve adjust/release button andpushing down on the head restraint.Properly adjust the hea

2. Simultaneously press and holdboth the adjust/release button andthe unlock/remove button, then pullup on the head restraint.To reinstall the adjusta

Using the power lumbar supportThe power lumbar control is located on the outboard side of the seat.Press the forward side of the controlfor additional

Move the switch in the direction ofthe arrows to raise or lower the rearportion of the seat cushion.Press the switch in the direction ofthe arrows to

Memory seat/power mirrors/adjustable pedals/steering columnThis system allows automaticpositioning of the driver seat,outside rearview mirrors, adjust

AdvanceTrac威 (if equipped):Displays when the AdvanceTrac威with RSC威 system is active. If thelight remains on, have the systemserviced immediately by yo

Heated seatsWARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cordinjury, medication,

Climate controlled seats air filter replacement (if equipped)The climate controlled seat system includes air filters that must bereplaced periodically

To install a filter:• First, position the filter in it’shousing making sure that the farforward end is all the way up inthe housing. Then push in on t

2. Locate handle on the side of theseat cushion by the door.3. Pull up on the handle and pushthe seatback forward toward thefront of the vehicle.To re

Placing the 2nd row outboard 40% seats in cargo modeWARNING: Use caution when folding the seatback to the flatback position as the system will move fo

Returning to the upright position from full lowered load floorpositionThe seatback cannot be returned to the upright position until the seat isreturne

To return the seat to a seating position:1. Push the seat down and latch tothe floor with a moderate amount ofeffort and speed.2. Make sure the seat i

Exiting the 3rd row1. Pull the strap located at thebottom outboard of the seat back torelease the seat from the floor, androtate the seat up towards t

WARNING: To prevent possible damage to the seat or safetybelts, ensure that the safety belts are not buckled when movingthe seat to the load floor pos

Adjusting the 2nd row center 20% seat (if equipped)Lift the handle to move the seatforward or backward.Note: This seat can be moved forward to keep a

High beams: Illuminates when thehigh beam headlamps are turned on.Key-in-ignition warning chime: Sounds when the key is left in theignition in the off

To operate the heated seats:• Push the indicated side of thecontrol for maximum heat.• Push again to deactivate.• Push the indicated side of thecontro

Folding down the 3rd row seats to the load floorWARNING: To prevent possible damage to the seat or safetybelts, ensure that the safety belts are not b

Third row power folding seat (if equipped)Note: Be sure that the headrestraints are folded down beforepowering the 3rd row seat down.The control butto

The power fold down seats will operate for 10 minutes after theignition switch is in off. The transmission must be in P (Park), andthe liftgate, or li

The fact that the pretensioners or airbags did not activate for both frontseat occupants in a collision does not mean that something is wrong withthe

Front safety belt energy management retractorsThe front outboard safety belt energy management retractors allowwebbing to be pulled out of the retract

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

Combination lap and shoulder belts1. Insert the belt tongue into the proper buckle (the buckle closest tothe direction the tongue is coming from) unti

Webbing extraction sensitive modeThe webbing sensitive locking mode locks the webbing and preventsmore belt from being pulled out if the belt is pulle

How to disengage the automatic locking modeUnbuckle the combination lap and shoulder belt and allow it to retractcompletely to disengage the automatic

Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,

Safety belt height adjustmentYour vehicle has safety belt heightadjustments for the driver and rightfront passenger. Adjust the height ofthe shoulder

To adjust the comfort guide:1. Slip the shoulder belt into thebelt guide. (The portion of the beltbetween the latch tongue and theD-ring, not the port

Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occup

If... Then...The driver’s safety belt is notbuckled approximately fiveseconds after the safety beltwarning light has turned off...The Belt-Minder威 fea

Reasons given... Consider...“Belts are uncomfortable” We design our safety belts to enhancecomfort. If you are uncomfortable -try different positions

WARNING: Do not sit on top of a buckled safety belt or insert alatchplate into the buckle to avoid the Belt-Minder威 chime. Todo so may adversely affec

4. Within approximately seven seconds of the light turning off, bucklethen unbuckle the safety belt.• This will disable the Belt-Minder威 feature for t

WARNING: All occupants of the vehicle, including the driver,should always properly wear their safety belts, even when an airbag supplemental restraint

WARNING: Additional equipment may affect the performance ofthe airbag sensors increasing the risk of injury.Children and airbagsChildren must always b

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the on position). The fuelgauge may vary slightly whe

• one or more impact and safing sensors and diagnostic monitor (RCM),• a readiness light and tone• the electrical wiring which connects the components

WARNING: Do not attempt to service, repair, or modify theairbag SRS, its fuses or the seat cover on a seat containing anairbag. Contact your authorize

The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of

WARNING: Do not attempt to service, repair, or modify theSafety Canopy威 system, its fuses, the A, B, C or D pillar trim, orthe headliner on a vehicle

• Two crash sensors mounted in the front doors (one on each side ofthe vehicle).• Two crash sensors located at the C pillar behind the rear doors (one

WARNING: If the SafetyCanopy威 system hasdeployed, the Safety Canopy威 willnot function again unless replaced.The Safety Canopy威 system(including the A,

The SOS Post-Crash Alert can be turned off when any one of thefollowing actions are taken by the driver or any other person:• pressing the hazard cont

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

Locks and Security 132Keys 132Locks 133Anti-theft system 144Seating and Safety Restraints 154Seating 154Safety restraints 173Airbags 186Child restrain

TRIP A/BRegisters the distance of individual journeys. Press and release INFObutton until the A or B trip appears in the display (this represents thet

If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestr

Installing child safety seats with combination lap and shoulderbeltsCheck to make sure the child seat is properly secured before each use.Children 12

1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear

9. Attach the tether strap (if the child seat is equipped). Refer toAttaching child safety seats with tether straps later in this chapter.10. Before p

Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol.The LATCH anchors are locat

WARNING: Never attach two child safety seats to the sameanchor. In a crash, one anchor may not be strong enough to holdtwo child safety seat attachmen

The tether strap anchors in your vehicle are in the following positions(shown from top view):• Second row bench seat• Second row bucket seatsAttach th

• Second row outboard seatingpositions• Second row center seatingposition (if equipped)3. Grasp the tether strap andposition it to the seat frame.4. R

5. Rotate the tether strap clip.6. Tighten the child safety seat tether strap according to themanufacturer’s instructions.Third row center seating pos

• Differences in the automatic shut-off points on the fuel pumps atservice stations• Variations in top-off procedure from one fill-up to another• Roun

3. Clip the tether strap through theanchor loop as shown.If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly

Booster seats position a child so that vehicle lap/shoulder safety belts fitbetter. They lift the child up so that the lap belt rests low across the h

Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

Note: Some systems show a message only if a condition is present.1. OIL LIFE2. CHARGING SYSTEM3. WASHER FLUID LEVEL4. DOOR STATUS5. LIFTGATE/GLASS6. B

INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air

The cold inflation pressure should never be set lower than therecommended pressure on the Safety Compliance Certification Label orTire Label.When weat

TIRE CAREInspecting your tires and wheel valve stemsPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones

WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressur

WARNING: Only use replacement tires and wheels that are thesame size, load index, speed rating and type (such as P-metricversus LT-metric or all-seaso

It is recommended that the two front tires or two rear tires generally bereplaced as a pair.The tire pressure sensors mounted in the wheels (originall

Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your

Note: If your tires show uneven wear ask an authorized dealer to checkfor and correct any wheel misalignment, tire imbalance or mechanicalproblem invo

4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new

8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n

UNITSDisplays the current units English or Metric.Press the RESET button to change from English to Metric.AUTOLAMPThis feature keeps your headlights o

13. Maximum Permissible Inflation Pressure: Indicates the tiremanufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti

When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.

Low Tire PressureWarning LightPossible cause Customer Action RequiredFlashing WarningLightSpare tire in use Your temporary spare tire is inuse. Repair

SNOW TIRES AND CHAINSWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel

capability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design performance. Before loadingyour vehi

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

Press the RESET button to select the running boards setting as follows:•AUTO: the running boards will automatically deploy when a door isopened and au

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400

• Thoroughly prepare your vehicle for towing. Refer to Preparing totow in this chapter.• Use extra caution when driving while trailer towing. Refer to

EngineRear axleratioMaximum GCWR -lb. (kg)Trailer weightrange (0 -maximum) - lb.(kg)4x25.4L withstandardtrailer towpackageAll 12000 (5443) 0–6000 (0–2

EngineRear axleratioMaximum GCWR -lb. (kg)Trailer weightrange (0 -maximum) lb. (kg)Navigator L 4x25.4L withstandardtrailer towpackageAll 12300 (5579)

Integrated hitch ratingThe standard integrated hitch has two ratings depending on mode ofoperation:• Weight carrying - requires a draw bar and hitch b

2. To reinstall the cover, insert thefour plastic tabs on top of the coverinto the corresponding slots, asshown in the illustration and pushthe cover

Most geographic areas (zones) have a magnetic north compass point thatvaries slightly from the northerly direction on maps. This variation is fourdegr

4. Attach the trailer to the vehicle and adjust the hitch equalizers so thatthe front bumper height is within a1⁄2” (13 mm) of the reference point.Aft

Driving while you towWhen towing a trailer:• Keep your speed no faster than 70 mph (113 km/h) during the first500 miles (800 km) of towing a trailer,

• If you will be towing a trailer frequently in hot weather, hillyconditions, at GCWR, or any combination of these factors, considerrefilling your rea

RECREATIONAL TOWINGFollow these guidelines if you have a need for recreational towing. Anexample of recreational towing would be towing your vehicle b

STARTINGPositions of the ignition1. Off— locks the steering wheel,automatic transmission gearshiftlever and allows key removal.2. Accessory— allows th

WARNING: If you smell exhaust fumes inside your vehicle, haveyour dealer inspect your vehicle immediately. Do not drive if yousmell exhaust fumes.Impo

4. Make sure the parking brake isset.5. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminate. See Wa

3. After idling for a few seconds, release the parking brake, apply thebrake, shift into gear and drive.Note: If the engine does not start on the firs

Guarding against exhaust fumesCarbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects.WARNING: If you smell exhaus

WARNING: Failure to follow engine block heater instructionscould result in property damage or physical injury.WARNING: To reduce the risk of electrica

CREATE MYKEY / CLEAR MYKEY / MYKEY SETUPFor more information refer to MyKey™ in the Locks and Securitychapter.ENGLISH / FRENCH / SPANISH RESET FOR NEW

• Finally, have the engine block heater system checked during your falltune-up to be sure it’s in good working order.How to use the engine block heate

Anti-lock brake system (ABS)On ABS-equipped vehicles, a noise from the hydraulic pump motor andpulsation in the pedal may be observed during ABS braki

Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.ADVANCETR

WARNING: If a failure has been detected within theAdvanceTrac威 with RSC威 system, the ⬙sliding car⬙ iconwillilluminate steadily. Verify that the Advanc

Note: If the system cannot be turned off, refer to MyKey™ in the Locksand Security chapter for more information.When AdvanceTrac威 with RSC威 performs a

Electronic Stability Control (ESC)Electronic Stability Control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa

Switching Off Traction ControlIf the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off the Traction Control feature

During trailer sway control events the “sliding car” icon in theinstrument cluster will flash momentarily. The cluster message centerwill also display

If the power steering system breaks down (or if the engine is turnedoff), you can steer the vehicle manually, but it takes more effort.If the steering

CHECK CHARGING SYSTEM — Displayed when the electrical systemis not maintaining proper voltage when the engine is running. If you areoperating electric

the system determines that the vehicle is low or high and needs to makea height adjustment while driving at speeds above 15 mph (24 km/h), thesystem w

BRAKE-SHIFT INTERLOCK – FLOOR-SHIFT TRANSMISSIONThis vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from be

WARNING: Do not drive your vehicle until you verify that thebrakelamps are working.WARNING: Always set the parking brake fully and make surethe gearsh

P (Park)This position locks the transmissionand prevents the rear wheels fromturning.To put your vehicle in gear:• Press the brake pedal• Start the en

D (Overdrive) with Tow/Haul OnThe Tow/Haul feature improvestransmission operation when towinga trailer or a heavy load. Alltransmission gear ranges ar

3 (Third)Transmission operates in third gear only.Used for improved traction on slippery roads. Selecting 3 (Third)provides engine braking.2 (Second)T

FORWARD AND REVERSE SENSING SYSTEMSThe forward and reverse sensing system will warn the driver of obstacleswithin a certain range of the front and rea

The reverse sensing portion of thesystem detects obstacles up to 6 ft.(2 m) from the rear bumper with adecreased coverage area at theouter corners of

WARNING: This system is not designed to prevent contact withsmall or moving objects. The system is designed to provide awarning to assist the driver i

Note: If the system cannot be turned off, refer to MyKey™ in the Locksand Security chapter for more information.The system defaults to enabled every t

CHECK AIR SUSPENSION (if equipped) — Displayed when the airsuspension system is not operating properly. If this message is displayedwhile driving, pul

Use the side mirrors and rearview mirror to get better coverage on bothsides and rear of the vehicle.Image delay if displayed through the rearview mir

WARNING: Do not use the camera system with the liftgateopen.If the back end of the vehicle is hit or damaged, then check with yourauthorized dealer to

• 4X2 - Momentarily illuminateswhen 2H is selected.• 4X4 AUTO – Illuminates when4X4 AUTO is selected.• 4X4 – Illuminates when 4X4 isselected.Modes of

maneuvers. This will disable the engine management feature, allowingthe vehicle to maintain full power and enhanced momentum through theobstacle.WARNI

Maintain steering wheel control at all times, especially in rough terrain.Since sudden changes in terrain can result in abrupt steering wheelmotion, m

If your vehicle gets stuckIf your vehicle gets stuck in mud or snow it may be rocked out byshifting between forward and reverse gears, stopping betwee

WARNING: Vehicles with a higher center of gravity such asutility and four-wheel drive vehicles handle differently thanvehicles with a lower center of

Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required f

“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nationswilderness are

Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;

KEY COULD NOT PROGRAM — Displayed when an attempt is madeto program a spare key using two existing MyKeys. Refer to MyKey™ inthe Locks and Security ch

WARNING: If you are driving in slippery conditions that requiretire chains or cables, then it is critical that you drive cautiously.Keep speeds down,

DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

Canadian customers refer to your Customer Information Guidefor information on:• coverage period• exact fuel amounts• towing of your disabled vehicle•

Note: With extended use, the flasher may run down your battery.FUEL PUMP SHUT-OFF SWITCHFUELRESETThe fuel pump shut-off switch is a device intended to

FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth

Passenger compartment fuse panelThe fuse panel is located under the right-hand side of the instrumentpanel.To remove the trim panel for accessto the f

The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtective Circuits1 30A Smart window #12 15A Driver side memory module3 15A Family ent

Fuse/RelayLocationFuse AmpRatingProtective Circuits23 15A High beam headlamps24 20A Horn25 10A Demand lamps, Glovebox, Visor26 10A Instrument panel cl

Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot

Customer Assistance 321Reporting safety defects (U.S. only) 327Reporting safety defects (Canada only) 327Cleaning 328Maintenance and Specifications 33

AUDIO SYSTEMSNote: If your volume is muted and MYKEY VOLUME LIMITED isdisplayed, refer to MyKey™ in the Locks and Security chapter for moreinformation

Fuse/RelayLocationFuse AmpRatingProtected Circuits4 — Trailer tow battery charge relay5 — Fuel pump relay6 — Electronic fan 1 relay7 — Rear window def

Fuse/RelayLocationFuse AmpRatingProtected Circuits32 40A** Blower motor relay33 — Not used34 30A** Auxiliary blower motor35 30A** PCM relay36 30A** Po

Fuse/RelayLocationFuse AmpRatingProtected Circuits59 15A* Heated mirrors60 — One-touch start diode61 — Fuel pump diode62 — Left HID headlamp relay63 2

CHANGING THE TIRESIf you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel

2. Full-size dissimilar spare with label on wheel: This spare tire hasa label on the wheel that states: “THIS TIRE AND WHEEL FORTEMPORARY USE ONLY”Whe

• Wet weather driving capability• All-Wheel driving capability (if applicable)• Load leveling adjustment (if applicable)When driving with the full-siz

Removing the jack and tools1. Open the liftgate, then locate theaccess panel on the floor behind the3rd row seat. Unlatch and removethe panel.2. Remov

Tire change procedureWARNING: To help prevent the vehicle from moving when youchange a tire, be sure the parking brake is set, then block thewheels (b

1. Block the wheels (both front orboth rear) on the opposite end ofthe vehicle from the wheel beingchanged. If on a grade, block bothwheels on the dow

WARNING: When one of the rear wheels is off the ground, thetransmission alone will not prevent the vehicle from moving orslipping off the jack, even i

THX: Your vehicle is equipped withthe THX威 II certified premium audiosystem. This system creates optimalacoustic quality for all seatingpositions and

• Never use the front or reardifferential as a jacking point.WARNING: To lessen the risk of personal injury, do not put anypart of your body under the

2. Slide the wheel partially underthe vehicle and install the retainerthrough the wheel center. Ifequipped, you may have to removethe wheel center cap

WARNING: When a wheel is installed, always remove anycorrosion, dirt or foreign materials present on the mountingsurfaces of the wheel or the surface

JUMP STARTINGWARNING: The gases around the battery can explode ifexposed to flames, sparks, or lit cigarettes. An explosion couldresult in injury or v

Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,

4. Make the final connection of the negative (-) cable to the jumpstarting stud located in the engine compartment, near the washer fluidbottle.Note: D

Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.

2. Remove the jumper cable on the negative (-) connection of thebooster vehicle’s battery.3. Remove the jumper cable from the positive (+) terminal of

4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery.After the disabled vehicle has been started and the jumper

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

4. MENU: Press MENU repeatedlyto scroll through the followingmodes:SATELLITE RADIO MENU (if equipped): Press MENU when satelliteradio mode is active t

If the vehicle is towed by other means or incorrectly, vehicledamage may occur.Ford Motor Company produces a towing manual for all authorized towtruck

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

If your vehicle must be serviced while you are traveling or living inCentral America, the Caribbean, or the Middle East, contact the nearestauthorized

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

Exterior chrome• Wash the vehicle first, using cool or lukewarm water and a neutral pHshampoo, such as Motorcraft Detail Wash (ZC-3-A).• Use Custom Br

• ENABLE ALERTS / DISABLE ALERTS: Press OK to enable/disablethe satellite alert status which alerts you when your selected songs areplaying on a satel

• Never apply any cleaning chemical to hot or warm wheel rims orcovers.• Some automatic car washes may cause damage to the finish on yourwheel rims or

• Never wash or rinse any ignition coil, spark plug wire or spark plugwell, or the area in and around these locations.PLASTIC (NON-PAINTED) EXTERIOR P

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENSClean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth,

• If grease or tar is present on the material, spot-clean the area firstwith Motorcraft Spot and Stain Remover (ZC-14). In Canada, useMotorcraft Multi

UNDERBODYFlush the complete underside of your vehicle frequently. Keep body anddoor drain holes free from packed dirt.FORD AND LINCOLN MERCURY CAR CAR

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

Working with the engine on1. Set the parking brake and shift to P (Park).2. Block the wheels.WARNING: To reduce the risk of vehicle damage and/orperso

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT5.4L V81. Windshield washer fluid reservoir2. Engine oil dipstick3. Brake fluid reservoir4. Engine coo

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

CHANGING THE WIPER BLADESIt is recommended that wiper blades are renewed before winter.To replace the wiper blades:1. Fold back the wiper arm andposit

Treble: Press / to adjust the treble setting. Press OK to close andreturn to the main menu.Balance: Press/ to adjust the audio between the right and l

4. To attach the new wiper to thewiper arm, align the cross pin andkeyway (denoted with the arrows)and firmly press the wiper bladeinto the wiper arm

• If the oil level is below thismark, engine oil must be addedto raise the level within thenormal operating range.• If required, add engine oil to the

Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by th

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the FULL COLD level or within theCOLD

• Do not mix coolants. Add the coolant type originally equippedin your vehicle. Refer to Maintenance product specifications andcapacities in this chap

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap.5. Fill the coolant reservoi

• NEVER increase the coolant concentration above 60%.• Increased engine coolant concentrations above 60% willdecrease the overheat protection characte

In TEXT MODE, press TEXT and then SEEK to view theadditional display text when “>” is active in the display.Satellite radio isavailable only with a

When this occurs the vehicle will still operate. However:• The engine power will be limited.• The air conditioning system will be disabled.Continued o

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsWARNING: Do not overfill the fuel tank. The pressure in anoverfilled tank may c

• Fuels can also be harmful if absorbed through the skin. If fuel issplashed on the skin and/or clothing, promptly remove contaminatedclothing and was

WARNING: When refueling always shut the engine off andnever allow sparks or open flames near the filler neck. Neversmoke while refueling. Fuel vapor i

When fueling your vehicle:1. Turn the engine off.2. Open the fuel filler door.3. Slowly insert the fuel filler nozzle fully into the fuel system. Pump

The use of leaded fuel is prohibited by law and could damage yourvehicle.Your vehicle was not designed to use fuel or fuel additives with metalliccomp

tank if you continue to use high quality fuel of the recommended octanerating. These products have not been approved for your engine andcould cause da

WARNING: Do not try to pry open or push open the EasyFuel™ system with foreign objects. This could damage the fuelsystem and its seal and cause injury

The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fu

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fuelecon

12. SHUFFLE: Press to play alltracks on the current disc in randomorder.13. AM/FM: Press to selectAM/FM1/FM2 frequency band.14. CD: Press to enter CD

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled mainten

• Do not turn off the ignition while your vehicle is moving, especially athigh speeds.• Have the items listed in scheduled maintenance informationperf

On board diagnostics (OBD-II)Your vehicle is equipped with a computer that monitors the engine’semission control system. This system is commonly known

If the service engine soon indicator is on or the bulb does notwork, the vehicle may need to be serviced. Refer to the On boarddiagnostics (OBD-II) de

5. If the fluid is low, add fluid in small amounts, continuously checkingthe level until it reaches the range between the MIN and MAX lines. Besure to

WARNING: To reduce the risk of vehicle damage and/orpersonal burn injuries do not start your engine with the aircleaner removed and do not remove it w

5. Release the three clamps thatsecure the cover to the air filterhousing. Push the air filter covertoward the center of the vehicle andup slightly to

10. Reconnect the mass air flowsensor electrical connector to theoutlet tube. Make sure the lockingtab on the connector is in the“locked” position (co

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationBrake fluidBetween MIN andMAX on rese

Item Capacity Ford part nameFord part number /Ford specificationCooling system stopleak pellets—Motorcraft CoolingSystem Stop Leak PelletsVC-6 /WSS-M9

Your vehicle is equipped with anAuxiliary Input Jack (AIJ) locatedinside the center console. TheAuxiliary Input Jack provides a wayto connect your por

Item Capacity Ford part nameFord part number /Ford specificationRear axlefluid–Conventionaldifferential(9.75 inch axle)4.5 pints (2.1L)Motorcraft SAE

ENGINE DATAEngine 5.4L V8 engineCubic inches 330Fuel 87 octane or (E-85)Firing order 1-3-7-2-6-5-4-8Ignition system Coil on plugSpark plug gap 0.039–0

Engine drivebelt routingIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations req

Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX

TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis

GENUINE LINCOLN ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Lincoln Accessories are available for yourvehicle through your local Lincoln o

Locking gas plug for capless fuel systemWheel locksFor maximum vehicle performance, keep the following information inmind when adding accessories or e

FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan3792010 Navigator (nav)Owners Guide (own2002), 1st PrintingUSA (fus)

7. Adjust the sound on your portable music player until it reaches thelevel of the FM station or CD by switching back and forth between theAUX and FM

AABS (see Brakes) ...261Accessory delay ...105AdvanceTrac ...263Air cleaner filter .

Child safety seats - boosterseats ...211Cleaning your vehicleengine compartment ...330instrument pa

Event data recording ...7Exhaust fumes ...258FFail safe cooling ...349Family entertainmen

JJack ...303positioning ...303storage ...303Jum

Power deployable runningboards ...109Power distribution box(see Fuses) ...296, 299Power door

Spark plugs,specifications ...367, 371–372Special noticeutility-type vehicles ...6Specification chart,lubricants ...

Your vehicle is equipped with a USBport inside your center console. Thisfeature allows you to plug in mediaplaying devices, memory sticks, andalso to

CONGRATULATIONSCongratulations on acquiring your new Lincoln. Please take the time toget well acquainted with your vehicle by reading this handbook. T

Note: After pressing the media button to select SYNC mode, press +or – to scroll through the different SYNC威 options: (SYNC USB, SYNCBTST and SYNC LIN

When the rear seat controls are activated, rear seat passengers can usethe controls to change the playing media for all passengers (Single Playmode) o

The front speakers remain playing for the front passengers. Press thespeaker button, or the 2/4 preset buttons simultaneously on the radioagain to dea

• Wipe discs from the center out.Don’t:• Expose discs to direct sunlight or heat sources for extended periodsof time.• Clean using a circular motion.C

Satellite radio informationSatellite radio channels: SIRIUS broadcasts a variety of music, news,sports, weather, traffic and entertainment satellite r

Note: SIRIUS reserves the unrestricted right to change, rearrange, addor delete programming including canceling, moving or adding particularchannels,

Radio Display Condition Action RequiredNO TEXT Artist information notavailable.Artist information notavailable at this time onthis channel. Thesystem

FAMILY ENTERTAINMENT DVD SYSTEM (IF EQUIPPED)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongl

3. Press the power button on theDVD player, then press Play tobegin to play the disc.If a DVD is already loaded into thesystem, press PLAY on the DVDp

3. The disc will begin to play andthe ‘CD Audio Disc’ screen willdisplay. From this screen, you canalso select from COMPRESSION,SHUFFLE and SCAN featu

Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti

2. Press the power button to turnthe DVD system on. The indicatorlight next to the power button willilluminate.3. Connect an auxiliary audio/videosour

Repeating each of these actions will switch back to single play mode, allspeakers playing and headphones off.A green light will illuminate next to eit

Using the infrared (IR) wireless headphones:1. Press the power control on the earpiece to turn the headphones ON.2. Select Channel A or B for each set

DVD player controls1. Headphone control A/B: Whilein Dual Play mode, press to selecteither the A or B headphone source.Then press MEDIA to select thed

4. (Fast forward): Press andrelease for the next chapter ortrack. Press and hold to forwardsearch a DVD, Video CD, or FES CD in DVD/CD mode.5./ (Play/

11. / (Headphones/Speakers): Press once for Dual Play(Headphone mode- the rear speakers are muted) and press again forSingle Play (same media playing

Remote controlUnless otherwise stated, all operations can be carried out with theremote control. Always point the remote control directly at the playe

7. VOL (Volume): When in Single Play, press to increase ( )ordecrease () the volume over all speakers. When in Dual Play, press toincrease () or decre

21. LANGUAGE (DVD dependent): Press to select the desiredlanguage.22. ENTER: Press to select the highlighted menu option.23. ILLUMINATION: Press to il

HeadphonesWireless headphonesWARNING: The driver should never use the headphones whiledriving the vehicle. Using headphones may prevent the driverfrom

Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance

To install the batteries, remove the screw at the bottom of the cover.Then, lightly press down on top and slide the cover off.When replacing the batte

To operate the headphones:• Press POWER on the ear piece to turn on the headphones. A redindicator light will illuminate indicating the headphones are

Wired headphonesWARNING: Do not leave children unattended in the vehicle anddo not let children operate the system while unsupervised. Ifwired headpho

Single Play: Single play consists of all occupants in the vehicle listeningto the same playing media over the front and rear speakers. When theDVD sys

Press the Headphone Control buttonA to change the audio source forChannel A.Press MEDIA to change the audiosource for Channel A. Thisinformation will

Press the Headphone Control buttonA to change the audio source forChannel A.Press MEDIA to change the audiosource for Channel A. Thisinformation will

Menu modePress MENU once on the DVD system to access the DVD disc menu ifavailable.Press MENU twice to access the DVD set-up menu and the followingfea

You can select from: WIDE, LETTERBOX or PAN SCAN. Once you havemade your selection, press ENTERto confirm. The LCD screen displaywill immediately chan

Once you have made your selection,press ENTER to confirm. This isdisc dependent.Audio CDsTo play audio CDs on your DVD system:1. Ensure that the vehic

4. The folder, track and elapsedtime will appear in the status bar.The screen will list the Artist, Title,Album and File Name.COMP (Compression):Compr

DATA RECORDINGService Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehi

CD, MP3 and CD player care• Handle discs by their edges only. Never touch the playing surface.• Do not expose discs to direct sunlight or heat sources

Playing a DVD1. Ensure that the vehicle is on or the ignition is in accessory mode.2. Ensure that the navigation system is on.3. Insert a DVD label-si

Frame by frame1. With a DVD playing, press pause.2. Press the right cursor button. TheDVD will advance one frame. Eachpress of the right cursor button

The B headphone jack (5) is locatedon the right side of the DVD system.Plug in wired headphones (notincluded) here.Note: The B headphones can onlyacce

There are three levels of control ofthe FES buttons. The states areFULL (enabled), LOCAL orLOCKED (disabled). To change the level of control, press th

rights owners. Use of this copyright protection technology must beauthorized by Macrovision Corporation, and is intended for home andother limited vie

WARNING: The driver should not attempt to operate anyfunction of the DVD system while the vehicle is in motion. Givefull attention to driving and to t

Care and service of the DVD playerEnvironmental extremesDVD players which are subjected to harsh environmental conditions maybe damaged or perform at

Cleaning DVD and CD discsInspect all discs for contamination before playing. If necessary, cleandiscs only with an approved DVD and CD cleaner and wip

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH REARPASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED)1.Defrost: Distributes outside air through the win

To access this information, special equipment must be directlyconnected to the recording modules. Ford Motor Company andFord of Canada do not access e

5. R Rear fan speed control: Press to enable the auxiliary systemor to adjust the rear fan speed from the front control. Press to manuallyincrease or

17. EXT: Press to display the outside temperature. Press again to displaythe cabin temperature settings. Note: Exterior readings are moreaccurate when

4.RRear defroster: Press to activate/deactivate the rear windowdefroster. Refer to Rear window defroster later in this chapter for moreinformation.5.

13. OFF: Outside air is shut out and the climate system is turned off.14. Driver temperature control: Press to increase or decrease thetemperature on

• During extreme high ambient temperatures when idling stationary forextended periods of time in gear, it is recommended to run the A/Cwith recirculat

AUXILIARY CLIMATE CONTROL (IF EQUIPPED)1. Fan speed: Turn to select thedesired fan speed.2. Temperature/mode selection:The distribution of air from th

HEADLAMP CONTROLRotate the headlamp control to thefirst positionto turn on theparking lamps.Rotate to the second positiontoturn on the headlamps.Rotat

Fog lamp controlThe headlamp control also operatesthe fog lamps. The fog lamps can beturned on when the headlampcontrol is in the, orpositions and the

WARNING: Always remember to turn on your headlamps atdusk or during inclement weather. The Daytime Running Lamp(DRL) system does not activate the tail

• (1) 8 feet (2.4 meters)• (2) Center height of lamp toground• (3) 25 feet (7.6 meters)• (4) Horizontal reference line2. Measure the height from thece

WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers use extreme caution

TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSFront row map lampsTo turn on

Second row map lampsThe second row map lamps arelocated in the headliner above thesecond row seats.The second row map lamp lightswhen:• any door is op

BULB REPLACEMENTLamp assembly condensationExterior lamps are vented to accommodate normal changes in pressure.Condensation can be a natural by-product

Function Number of bulbs Trade number2nd row reading lamp 1 1600XBRear cargo lamp 1 211–2XBRear turn/tail/brakelamps4 4057KBackup lamps 2 921Supplemen

3. At the back of the headlamp lens,remove the two headlamp assemblybolts.4. Pull the headlamp assemblyforward slightly to expose theelectrical connec

1. Make sure the headlamp switch isin the off position.2. Open the liftgate to expose thelamp assembly screws.3. Remove the two screws from thelamp as

Replacing the high-mount brakelampTo change the high-mountbrakelamp bulbs:1. Remove the two screws holdingthe lamp assembly in place.2. Pull the lamp

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Courtesy wipe feature: One extra wipe will occur a few seconds afterwashing the front window to clear any excess washer fluid remaining onthe windshie

POWER TILT STEERINGThe steering column can beadjusted manually by moving thetwo-way rocker adjustment controllocated below the turn signal/wipercontro